| Brand: | Pylontech |
| Product Code: | Powercube-M3A-100-1113V |
| Reward Points: | 63000 |
| SKU : | Pylontech M3100 1113V |
| Dimension | 500km | 750km | 1000km | +++ |
|---|---|---|---|---|
| Box-Shippment | 1day | 2 day | 3 day | 5 day |
| By Truck | 3 day | 4 day | 5 day | 7 day |
Tags: pylontech lifepo4, pylontech battery, pylontech 1113.6Volt Powercube M3A 100, S1500M3A100, LFP
If LiFePO4 batteries are not fully discharged, they do not need to be charged after each use. LiFePO4 batteries do not get damaged when left in a partial state of charge (PSOC). You can charge your LiFePO4 batteries after each use or when they have been discharged up to 80% DOD (20% SOC). If the Battery Management System BMS) disconnects the battery due to low voltage (voltage will be <10V), remove the load and charge immediately using a LiFePO4 battery charger.
LiFePO4 batteries can be safely charged between 0°C to 45°C (32°F to 113°F). LiFePO4 batteries do not require temperature compensation for voltage when charging at hot or cold temperatures. All Canbat LiFePO4 batteries come with an internal BMS that protects the battery from low and high temperatures. If the BMS disconnects due to low temperature, the battery must warm up for the BMS to reconnect and accept the charging current. If the BMS disconnects because of high temperature, the battery will need to cool down before the BMS will accept charging the battery. Please refer to your specific battery’s datasheet for the BMS low temperature and high-temperature cut-off and reconnect values.
The charging and discharging temperature for lithium batteries from our LT series is -20°C to 60°C. Canbat Low Temperature (LT) Lithium Batteries are cold-weather rated, designed for Canada’s cold climates. These batteries have a built-in heating system featuring proprietary technology that draws power from the charger. No additional components are required. The entire process of heating and charging is completely seamless. The heating system automatically activates once charging below 0°C is attempted, and it automatically deactivates when it’s no longer needed. The heating system does not take power from the battery, but rather from the charger, ensuring the lithium battery is not discharging itself and keeping you powered. Simply plug the LT lithium battery into the LiFePO4 charger and the internal heating and monitoring systems take care of the rest.
Most lead-acid battery chargers can be used with LiFePO4 batteries as long as they are within the appropriate voltage guidelines. AGM and Gel algorithms typically fall within the LiFePO4 voltage requirements. The voltage for flooded battery charging algorithms is often higher than LiFePO4 charging requirements, which will result in the BMS disconnecting. If this happens, it is generally good practice to replace your charger for one with a LiFePO4 charge profile. Since the BMS protects the battery, using lead-acid chargers will typically not damage the battery.
Note that if the BMS disconnects due to low voltage, a lead-acid battery charger may not be able to reconnect the BMS, even if the charger has the acceptable charging parameters to charge LiFePO4. This is because when the BMS disconnects, the lithium battery will not have a voltage as it will read 0V on a voltmeter, while lead-acid chargers require the battery to read out a voltage to start charging. If the battery is reading 0V, the lead-acid battery charger will not be able to understand that a battery is connected and that it should start charging. This is also true for some low-quality lithium chargers. It is always recommended that you invest in a high-quality LiFePO4 charger to ensure high performance and longevity. Feel free to contact Canbat should you have any questions.
When connecting LiFePO4 batteries in parallel, please make sure each battery is within 0.1V of each other before putting them in service, This will minimize the chance of imbalance between batteries. If you’re charging 12V LiFePO4 batteries, the charging voltage should be between 14V – 14.2V. When charging 24V batteries in parallel, the charging voltage should be 28V – 28.4V. Charging 36V lithium batteries in parallel requires a voltage of 42V – 42.6V. Finally, charging 48V LiFePO4 batteries require voltage parameters of 56V – 56.8V. Below is a table with a summary showing the voltage requirements for each system voltage.
| System Voltage | Charging parameters |
| 12V | 14V – 14.2V |
| 24V | 28V – 28.4V |
| 36V | 42V – 42.6V |
| 48V | 56V – 56.8V |
The voltage parameters apply to both charging profiles CC and CC-CV. If your charger’s voltage is lower than those listed in the table, it will not damage your battery, but it will be undercharged, and it will not provide the full rated capacity of the battery. If your charger’s voltages are higher than those listed in the tables above, the BMS may disconnect the battery and you may have to remove the load to reconnect. We recommend you replace the charger to avoid this inconvenience and to invest in a high-quality LiFePO4 battery charger.
When connecting batteries in series, please make sure each battery is within 50mV (0.05V) of each other before putting them in service. This will minimize the chance of an imbalance between batteries. If your batteries get out of balance, the voltage of any battery is >50mV (0.05V) from another battery in the set, you should charge each battery individually to rebalance. You can charge each battery individually periodically to avoid imbalance. When charging LiFePO4 batteries in series, it is best to use a multi-bank charger that charges each battery individually to ensure the cells remain balanced. You can also use a 24V battery LiFePO4 charger or a 48V battery LiFePO4 charger if you’d like to charge your system as a whole.
Below are the key, typical charger inputs when using an inverter/charger or charge controller for charging LiFePO4 batteries. Many inverter/ chargers require additional parameters, please contact Canbat technical support for assistance. LiFePO4 batteries do not require equalizing. LiFePO4 batteries do not require temperature compensation for voltage when charging at hot or cold temperatures.
| PARAMETER | 12V SYSTEM | 24V SYSTEM | 36V SYSTEM | 48V SYSTEM |
| Bulk Voltage | 14V – 14.6V | 28V – 29.2V | 42V – 43.8V | 56V – 58.4V |
| Absorption Voltage | 14V – 14.6V | 28V – 29.2V | 42V – 43.8V | 56V – 58.4V |
| Absorption Time | 0- 6 min | 0- 6 min | 0- 6 min | 0- 6 min |
| Float Voltage | 13.8V ± 0.2V | 27.6V ± 0.2V | 41.4V ± 0.2V | 55.2V ± 0.2V |
| Low Voltage Cutoff | 11V | 22V | 33V | 44V |
| High Voltage Cutoff | 14.6 | 29.2V | 43.8V | 58.4V |
Depending on the quality of the alternator, it may work fine to charge LiFePO4 batteries without modifications. However, low-quality alternators with poor voltage regulation can cause the BMS to disconnect LiFePO4 batteries. If the BMS disconnects the batteries the alternator may be damaged. To protect your LiFePO4 battery and alternator, please be sure to use a compatible high-quality alternator or install a voltage regulator. You can also use a DC to DC charger to safely and effectively charge your batteries including house banks. Installing a DC to DC charger is the recommended option when it comes to charging lithium with an alternator.
If you are using a voltage-based fuel gauge that is designed for lead-acid batteries, it will not accurately measure the state of charge (SOC) of LiFePO4 batteries. Please replace your fuel gauge with one that measures current rather than voltage to accurately measure the state of charge of lithium iron phosphate batteries.
If you have any technical questions, please contact Canbat Technical Support at +1 778-358-3925.
Yes, you can charge Canbat lithium batteries with solar panels. In fact, you can charge them with any type of charging equipment, as long as the charging voltage is within 14V to 14.6V for our 12V LiFePO4 batteries.
Yes, but it is recommended to invest in a DC to DC charger to protect your LiFePO4 battery and alternator.
Most lead-acid battery chargers can be used with LiFePO4 batteries as long as they are within the appropriate voltage guidelines. AGM and Gel algorithms typically fall within the LiFePO4 voltage requirements. The voltage for wet cell or flooded battery charging algorithms are often higher than LiFePO4 requirements, which will result in the BMS disconnecting the battery at the end of the charge cycle, and may result in the charger displaying an error code. If this happens, it is generally good practice to replace your charger. Since the BMS protects the battery, using lead-acid chargers will not damage the battery.
LiFePO4 batteries can safely charge between 0°C to 45°C (32°F to 113°F). If your application requires you to recharge in freezing temperatures, Canbat Low Temperature series (LT) can be recharged between -20°C to 45°C (-4°F to 113°F). The LT series has a built-in heating system featuring proprietary technology that draws power from the charger itself. No additional components are required. The entire process of heating and charging is completely seamless. The heating system automatically activates once charging below 0°C is attempted, and it automatically deactivates when it’s no longer needed. The heating system does not take power from the battery, but rather from the charger, ensuring the battery is not discharging itself. Simply plug the battery into the lithium charger and the internal heating and monitoring systems take care of the rest.
The short answer is no. In order to fully charge a 12V LiFePO4 battery, a charger with a voltage of 14V to 14.6V is required. Most AGM battery chargers are within that range and they would be compatible with Canbat lithium batteries. If you have a charger with a lower voltage, it may still charge the battery, but it won’t charge it to 100%. A charger with a higher voltage would not charge the battery and the BMS would enter protection mode due to its high voltage disconnect feature. Although many AGM battery chargers are compatible with LiFePO4, wet cell or flooded battery chargers are not compatible as they typically charge at a higher voltage.
Canbat LiFePO4 batteries can be discharged up to 100% of their capacity. However, to optimize the performance of your LiFePO4 battery, to achieve a higher cycle life, and to avoid the BMS disconnecting the battery, we recommend limiting the discharge to 80%. If the BMS disconnects the battery due to low voltage, at 100% depth of discharge, remove the load and recharge using a LiFePO4 charger to reactivate the BMS.
LiFePO4 batteries can safely discharge between -4°F to 140°F (-20°C to 60°C). All Canbat LiFePO4 batteries come with a built-in BMS that protects the battery from low-temperatures and high-temperatures. If the BMS disconnects due to cold or high temperature, wait until the temperature is more suitable and the BMS will reconnect automatically.
It is recommended to store LiFePO4 batteries at about 50% state of charge (SOC). If the batteries are stored for long periods of time, cycle the batteries at least every 6 months. Do not store batteries that are discharged. They do not require a trickle charger. · Recommended storage temperature: -5 to +35°C (23 to 95 °F) · Storage up to 1 month: -20 to +60°C (4 to 140 °F) · Storage up to 3 months: -10 to +35°C (14 to 95 °F) · Extended storage time: +15 to +35°C (59 to 95 °F) It is highly recommended to store lithium batteries indoors during the offseason.
Yes, you can connect up to four 12V batteries of the same model in series to obtain a higher voltage. Do not connect lithium batteries in both parallel and series simultaneously. Please note that the 24V lithium batteries are designed for 24V applications and do not support series connections. Likewise with the 36V and 48V lithium batteries. When charging LiFePO4 batteries in series, it’s recommended to use a multi-bank battery charger that can charge each battery individually. If that’s not an option, you can also use a 24V battery LiFePO4 charger or a 48V battery LiFePO4 charger if you’d like to charge your system as a whole. Canbat lithium batteries support charging in series.
Yes, you can connect up to four 12V batteries of the same model in parallel to obtain a higher capacity. Do not connect lithium batteries in both parallel and series simultaneously. Canbat 24V and 36V lithium batteries also support up to 4 units in parallel. Canbat 48V LiFePO4 batteries support up to 14 units in parallel as they are designed for larger projects. Canbat lithium batteries support charging in parallel.
Yes, Canbat LiFePO4 batteries can be installed upright or on their sides. Please fasten the battery if installed in a moving vehicle, such as in an RV or a boat. Please also avoid placing anything over the battery, and it’s recommended to cover the terminals with a plastic cap to prevent an external short circuit.
Yes, LiFePO4 is a safe chemistry and the most stable lithium-type battery on the market. Canbat lithium is UL 1642 certified, which means they have been tested for short-circuit, abnormal charging, crush, impact, shock, vibration, heating, temperature cycling and pressure. All Canbat LiFePO4 batteries come with an internal Battery Management System. The BMS protects against
If you already have a lead-acid or a LiFePO4 charger and you want to make sure it’s compatible, chat with one of our battery experts. We can check your charger’s user manual and confirm the voltage parameters. Canbat offers Canada-based 24/7 chat support to all its clients.
This battery is formed by:
Pylontech Powercube M3A-100 Energy storage system consists of 1x S1000M3A100 Main controller BMS and 1-29 HM3A180 5683wh (vah) Battery modules each
Pylontech Powercube 19pcs x HM3A100(5680wh) module +1 pcs S1000M3A100 = 107980wh
HM3A180(5680wh) is 55 kg, S1000M3A100 is 24kg, 2100mm high cabinet is 230kg
Powercube M series products with its modular design concept, enables the highest flexibility both for rack mounted and container based constructions, giving the flexibilities for customer to deploy the system nearly in any nodes in the grid, supporting the services such as emergency power, new energy stabilizer,energy shifting, load shaving, grid stabilizer, frequency responding (under de velopment). With our deep experience in BESS (battery energy storage system), vertical industrial chain consolidation and fantastic
PowerCube-M3A 100 is a high voltage battery storage system based on lithium iron phosphate battery, is one of new energy storage products developed and produced by Pylontech, it can be used to support reliable power for various types of equipments and systems. PowerCube-M3A 100 is especially suitable for application scene of high power, limited installation space, restricted load-bearing and long cycle life.
PowerCube-M3A 100 has 3 levels BMS (battery management system）, which can manage and monitor cells information including voltage, current and temperature. What’s more, BMS can balance cells charging and discharging to extend cycle life. Multiple batteries can connected in parallel to expand capacity and power in parallel for larger capacity and longer power supporting duration requirements.
Along with the wide deployed residential ESS Phantom series, Pylontech is proud to announce our High Voltage energy storage system serving the commercial/industrial/grid level customers –
Powercube series. Powercube series products with its modular design concept, enables the highest flexibility both for rack mounted and container based constructions, giving the flexibilities for customer to deploy the
system nearly in any nodes in the grid, supporting the services such as emergency power, new energy stabilizer,energy shifting, load shaving, grid stabilizer, frequency responding (under development). With our deep experience in BESS (battery energy storage system), vertical industrial chain consolidation and fantastic ROI control, Pylontech Powercube will be your trustable system in all ESS application.
Features
The whole module is non-toxic, non-polluting and environmentally friendly;
Cathode material is made from LiFePO4 with safety performance and long cycle life;
Battery management system (BMS) has protection functions including over-discharge, over-charge, over-current and high/low temperature;
The system can automatically manage charge and discharge state and balance current and voltage of each cell;
Flexible configuration, multiple battery modules can be in serial for expanding voltage and Capacity.
Adopted self-cooling mode rapidly reduced system entire noise;
The module has less self-discharged, up to 6 months without charging ion shelf; no memory effect, excellent performance of shallow charge and discharge;
Working temperature range is from 10℃ to 40℃, with excellent discharge performance and cycle life;
Small size and light weight, standard of 19-inchembedded designed module is comfortable for installation and maintenance;
| Products Type | S1500M3A100 |
| System Operation Voltage | 1000 Vac |
| Charge Current | 150A |
| Discharge Voltage | 38.4V-1228V Dc |
| Self Consumption Power | 8Wh |
| Dimension | 330x628x150.5mm |
| Communication | RS 485, CAN |
| Protection Class | IP65 |
| Operation Temperature(℃) | -20~65 |
| Storage Temperature(℃) | -40~80 |
| Products Type | HMA3A 100 | |
| Battery Module Voltage(Vdc) | 38V | |
| Battery Module Capacity(AH) | AH148 (5680Wh) | |
| Battery Cell Quantity(pcs) | 30 (118.4Wh/cell) | |
| Battery Module Charge Current | 14,8A | |
| Battery Module Charge Current Normal | 148A | |
| Battery Module Charge Current Max | 240A | |
| Battery Module Discharge lower-Voltage | 27V | |
| Operation Temperature(℃) | 0-50ºC | |
| Dimension | 442x390x132mm 64kg |
System Advantages
It is possible to connect several HV batteries in series to increase the capacity of the storage system. Some inverters have a working voltage range on the DC side e.g. of 100V-550V. When using a battery stack on such inverters, e.g. 3 pieces H38240 are required.
The battery management system (BMS) S1000M2A240 has protective functions, including protection against excessive discharge
Protection against overvoltage
Protection against overload
Protection against excessively high or low temperatures.
The system can automatically manage the charge and discharge status and balance the current and voltage of each cell. The control module has two types of power supply, either an internal power supply or an external power suppl
Energy Density 145Wh/kg Small volume, Light weight ,Normal cycle life more than 6000 Safety cert: CE、TÜV、TLC、UL、ROHS ,Conformance to QC/T743-2006 testing standard
1. Self-Consumption Optimization High energy demand in the morning and evening but sol ar gener ation i s mos t sufficient during the Mid-Day. Battery Storage system balance the feeding and demands. Realize your grid independence.
2. Benefits fromPeak Shaving
House: Load Shifting Store the power during low-peak andusetheenergy at peak-time. Save the money which happens arising from peak rate. Transmission&Distribution: peak ShavingSave on the electricity bills by reducing peak demand
3. VPP Revenue
Enabling a cost reduction, as well as boosting the system’s efficiency
Product Warranty
Pylontech warrants that the Product will remain free of defects caused by improper workmanship or defective materials.
This warranty continues for a Two (2) years from the earlier of:
1. the date of installation of the Product; or
2. six (6) months after the date the Product was manufactured,
This warranty does not include any accessories and tool kit items provided with the Product. This is a limited warranty only covers the repair or replace of a defective Product.
Pylontech will repair or replace the Product if the Product is defective and returned during the Warranty Period. The repaired or replaced product will continue the original remaining warranty period. In either case it shall not justify as a renewal of the warranty period.
| Battery Comparison Criteria | LifePo4 Battery | Jel/AGM/Opzs Lead Acid Battery |
| Number of Cycles 80% Deep Discharge | 6000 | 600 |
| Efficiency | %96 | %85 |
| Charging time 80% Capacity | 2 Hour | 8 Hour |
| Safe Capacity Usage | %80 | %60 |
| Maintenance Requirement | No | Yes |
| Voltage Stability(%100-%10) | 14V/12.4V | 13V/11.51V |
| weight100AH 12V | 12 kg | 30 kg |
| Operating Temperature (without capacity loss) | -20ºC~ 60℃ | 20ºC ~ 25℃ |
| Impact vibration resistance | Çok iyi | iyi |
| Shelf Life -Calendar Life | 15 Sene | 12 Sene |
| Standby Discharge Rate | %2 | %3 |
| Maximum withstand temperature | 90ºC | 60ºC |
| Require Special Charger | No | No |
| Cell Voltage | 3.2V | 2V |
| Output power Stability 90% discharge | Fixed | Variable |
| Instant Maximum Discharge Current 100AH | 300aH | 300AH |
| Maximum Charge Current At Empty | 100Ah | 30AH |
| 1 Hour Discharge Capacity | 90Ah | 59AH |
| Maximum Guarantee Given | 12 Sene | 2 Sene |
| Protection | BMS/Elektronik | Koruma Yok |
| How long has it been used | 1996/( 2017 populer) | 1950/(1970 populer) |
| Toxic Waste | No | Yes/Lead |
| Recycling | Mo | %100 recycling |
| Repair/Recovery | No | Possbile |
| Serial Parallel Connected | No | Yes |
| Quality Classes | A,B,C Grade | A,B Grade |
| In case of short circuit | Withouth BMS Explasion | Intense gas will be released |
| Can it be transported by plane | Yes(UN3091 UN3481) | YEs |
| Performance below 0ºC | Charge No, Decharge Yes | Charge and Descharge |
| Overcharge | Demaged | Only capacity lost |
| Breakdown | high | Seldom |
Durability | Weak | High |
| Reliability | Weak | High |
| Use of | Dificult | Easy |
| Replace new one | Dificult and high cost | Easy and Cheap |
| Scrap price | No Sale Scrapt | 1USD/kg |
| Battery Electrical Features | |
| Battery Nominal Capacity Ah | 148 |
| Battery Nominal Capacity wh | 164810 |
| Battary Voltage Volt | 1113 |
| Battery Types | LifePo4 |
| LifePo4 Battery Type | Rack mount |
| Battery Cycle Use | 5000 |
| BMS Charge Current Amper | 74 |
| BMS Decharge Current Amper | 150 |
| LifePo4 Paralellel Serial | Serial-Parallel |
| LifePo4 Communication | CAN, Modbus RTU/TCP/IP |
| Battery Internal Resistance mΩ 25°C | 210 |
| Maximum Discharge Current Amper | 140 |
| Absorption Charge Current Amper | 29 |
| Battary Float Voltage Volt | 1252 |
| Self Descharge 25ºC % | 2 |
| Battery Features | CAN, Modbus RTU/TCP/IP |
| Battery Mechanical Features | |
| Battery Dimension | 805x845x2130mm (31.69x31.69x83.86inch) |
| Battery Weight kg | 1798 |
| Battery Terminal Type | Plug |
| Battery Certificates | |
| Battery Design Life Years | 15 |
| Battery Made In | China |
| Battery Certificates | UL1973/IEC62619/VDE/CE |
| Battery Warranty Time | 10 |
| Battery Customer Rate %100 | 85 |
988,758.00₺ 1,004,934.00₺ Ex Tax: 823,965.00₺
853,284.00₺ 865,416.00₺ Ex Tax: 711,070.00₺
2,551,764.00₺ 2,588,160.00₺ Ex Tax: 2,126,470.00₺
4,852,800.00₺ 5,176,320.00₺ Ex Tax: 4,044,000.00₺
950,340.00₺ 970,560.00₺ Ex Tax: 791,950.00₺
1,876,416.00₺ Ex Tax: 1,563,680.00₺
1,496,280.00₺ Ex Tax: 1,246,900.00₺
1,637,820.00₺ 1,678,260.00₺ Ex Tax: 1,364,850.00₺
2,264,640.00₺ 2,345,520.00₺ Ex Tax: 1,887,200.00₺
12,536,400.00₺ 12,940,800.00₺ Ex Tax: 10,447,000.00₺
14,154,000.00₺ 14,962,800.00₺ Ex Tax: 11,795,000.00₺
12,334,200.00₺ 12,536,400.00₺ Ex Tax: 10,278,500.00₺
14,154,000.00₺ 14,962,800.00₺ Ex Tax: 11,795,000.00₺
12,334,200.00₺ 12,536,400.00₺ Ex Tax: 10,278,500.00₺
23,859,600.00₺ 24,264,000.00₺ Ex Tax: 19,883,000.00₺
28,510,200.00₺ 28,712,400.00₺ Ex Tax: 23,758,500.00₺
31,947,600.00₺ 32,352,000.00₺ Ex Tax: 26,623,000.00₺
27,499,200.00₺ 27,499,200.00₺ Ex Tax: 22,916,000.00₺
