Prior to installing modules please obtain information about any requirements and necessary approvals for the site, installation and inspection from the relevant authorities.

SAFETY INSTRUCTIONS

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries and all appropriate sections of this manual.

2. CAUTION --To reduce risk of injury, charge only deep-cycle lead acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.

3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.

4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.

5. CAUTION – Only qualified personnel can install this device with battery. 6. NEVER charge a frozen battery.

7. For optimum operation of this inverter/charger, please follow required spec to select appropriate cable size. It’s very important to correctly operate this inverter/charger.

8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.

9. Please strictly follow installation procedure when you want to disconnect AC or DC terminals. Please refer to INSTALLATION section of this manual for the details.

10. Fuses (3 pieces of 40A, 32VDC for 1KVA, 4 pieces of 40A, 32VDC for 2KVA and 6 pieces for 3KVA, 1piece of 200A, 58VDC for 4KVA and 5KVA) are provided as over-current protection for the battery supply.

11. GROUNDING INSTRUCTIONS -This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulation to install this inverter. 

12. NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC input short circuits.

13. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this inverter/charger back to local dealer or service center for maintenance. Maximum Panel Connection Type, Number Of module

280W Solar Panel Minimum 1Series, Maximum 2 Series, Maximum 5 Module

340W Solar Panel Minimum 1 Series, Maximum 2 Series, Maximum 4 Module

400W Solar Panel Minimum 1 Series, Maximum 1 Series, Maximum 3 Module

455Wat Solar Panel Minimum 1 Series, Maximum1 Series, Maximum 3  Module

· Check applicable building codes to ensure that the construction or structure (roof, facade, support, etc.) can bear the module system load.

· CS-series solar modules have been qualified for Application Class A (equivalent to Safety Class II requirements). Modules rated under this class should be used in systems operating at voltage above 50 V or power above 240 W, where general contact access is anticipated.

· Atakale Solar Inc. modules have been certified  as Type 1 or Type 4 according to UL 1703 andClass C according to IEC 61730-2, please refer to the datasheet or the product nameplate for the detailed types.

· Consult your local authority for guidelines and requirements for building or structural fire safety When installing modules, ensure the supporting roof has a fire resistant roof covering rated for the application. · The fire rating for this module is only valid when the product is installed as specified in the mechanical mounting instructio

The module is intended for use in general open-air climates, as defined in IEC 60721-2-1: Classification of environmental conditions Part-2-1: Environmental conditions appearing in nature - Temperature and humidity.

· Please consult the atakale Solar Inc. technical  support department for more information on the  use of modules in special climates, , such as an altitude greater than 2000 m.

Exposing modules to salt (i.e. marine environments) or sulfur (i.e. sulfur sources, volcanoes) incurs the risk of module corrosion. · Do not expose modules and their   onnectors to any unauthorized chemical substances (e.g. oil, lubricant, pesticide, etc.), as modules may incur damages.

· Failure to comply with these instructions will void atakale Solar Inc. limited warranty

Features

 Pure sine wave inverter

•  Built-in MPPT solar charge controller
•  Configurable input voltage range for home appliances and personal computers via LCD setting
•  Configurable battery charging current based on applications via LCD setting
•  Configurable AC/Solar Charger priority via LCD setting
•  Compatible to mains voltage or generator power
•  Auto restart while AC is recovering
•  Overload/ Over temperature/ short circuit protection
•  Smart battery charger design for optimized battery performance
•  Cold start function

Basic System Architecture 

The following illustration shows basic application for this inverter/charger. It also includes following devices to have a complete running system:

 Generator or Utility. 

 PV modules (option)

Consult with your system integrator for other possible system architectures depending on your requirements. This inverter can power all kinds of appliances in home or office environment, including motor-type appliances such as tube light, fan, refrigerator and air conditioner.